建筑工程模板

自动切割生产线

Automatic cutting production line

这机组由电脑数控玻璃切割机、玻璃自动上片台、玻璃掰片台三部分组成。操作方便，使用范围广、切割速度高、启动和刹车快、稳、准等特点。品牌电脑和意大利最流行的玻璃排版软件保证了输入方式和排版最优化。该机组取片、送片、切割、掰片整个过程实现全自动化操作，生成效率高，劳动强度低，特别适合于批量生产。

This unit is mede up of three parts of the computer numerical control glass cuttingmachine, glass automatic upper piece table and glass breaking piece table. Easy tooperate, using a wide range of cuttingHigh speed, start and brake fast, stable, accurateandso on Brand computers and ltalys most popular glass typesetting softwareensuresthat the input method and layoutOptimization The whole process of thegenerating unittakes film, film feeding, cutting and breaking off pieces to realizeautomatic operation,high production efficiency and low labor intensityMass production.

四边磨玻璃生产线

Four edges grinding glass production line

全自动卧式玻璃四边直线磨边机与自动上片台、清洗机和自动下片台灯设备匹配形成自动玻璃加工联线机组，以高加工精度、高效率、高机械配置组合成为该加工领域的最强配套设备。本机组采用人机操作，PLC控制，六轴饲服电机控制，四轴联动，自动识别玻璃尺寸，棱角加工速度达30米/分;且不同规格和厚度的玻璃可连续上片，无需人工调整定位和等待，以皮带式真空吸力传送及固定玻璃后加工磨边和除膜有效避免玻璃划伤和表面压痕。

Automatic glass processing line machine matched with automatic horizontal glassedge grinding machine and automatic upper piece table, washing machine and automatic lower piece desk lamp deviceHigh processing precision, high efficiency, highmechanical combination of the processing field to become the strongest supportingequipment. This unit uses man-machine operation,PlC control, six axis servo motorcontrol, four axis linkage,automatic identification of glass size.

钻孔机玻璃生产线

Drilling machine glass production line

该机采用计算机数控系统控制，由交流同服系统实现X、Z、W轴三个方向的精确定位。此产品钻孔效率很高，孔位准确，是幕墙玻璃和其他大规格批量包里钻孔的首选优质配套设备。

This machine uses the computer numerical control system control, realizes the X, theZ, the W axis three directions precise localization by the AC servo system. Drilling effi-ciency of this productHigh, hole position eccuracy, is the first choice of high qualityequipment for curtain wall glass and other large size batch package.

焊接

Welding Steel

对首次采用的钢材、焊接材料焊接方法、焊后热处理等进行焊接工艺评定，并根据评定报告确定焊接工艺;焊接工艺评定符合《建筑钢结构焊接规程》GBJ81-91;焊工全部经过考试并取得合格证;焊丝在使用前清除油污、铁锈;焊条、焊丝使用前按说明书规定的烘焙时间和温度进行烘焙;焊缝外形尺寸符合现行国家标准《钢结构焊缝外形尺寸》GB10854-89;探伤焊缝条例国家标准《钢焊缝手工超声波探伤方法和探伤结果分级》GB11345-89的规定

The welding process of the first steel, welding material, welding method and post-welding heat treatment was evaluated, and the welding process was determined according to the evaluation report Welding process assessment in accordance with the“Building steel structure welding code” GBJ81 -91; welders all passed the examination and obtain a certificate; The welding rod and wire are baked according to the baking time and temperature stipulated in the instruction before use. The weld shape size conforms to the current national standard“Steel structure weld shape size” GB10854 -89; The national standard“Manual ultrasonic testing method and classification of testing results for steel welds”(GB11345 -89)

立组

Automatic centring and setting machine

H型钢组装采用中间焊点、自动对中组立机;组装前，零件、部件全部检查合格;连接接触面和没焊缝边缘30-50mm范围内的铁锈毛刺、污垢、冰雪等清理干净。组装精度完全满足国家标准《钢结构工程施工及验收标准》GB50205-2001规定

The hbeam Assembly adopts intermediate solder joint and automatic centering assembly machine Connect the contact surface and no weld edge 3050mm range of rust burrs, dirt, ice and snow clean. Assembly accuracy fully meet the national standard“Steel construction and acceptance standards” GB50205-2001

矫正

Corrective Steel      

碳素结构钢在环境温度低于-16℃时，低合金结构钢在环境温度低于-12℃不得进行冷矫正时，加热温度不得超过900℃;矫正后的钢材表面，无明显的凹痕或损伤，划痕深度小于0.5mm;钢结构矫正后的偏差符合现行国家标准《钢结构工程施工及验收规范》GB50205-2001.

Low alloy structural steel shall not be subjected to cold correction at ambient temperature below -12 ° C, and the heating temperature shall not exceed 900 ° C for carbon structural steel at ambient temperature below -16 ° C, no obvious dent or damage, the scratch depth is less than 0.5 mm, the deviation after correction conforms to the current national standard“Code for construction and acceptance of steel structure engineering” GB50205-2001.

抛丸除锈

Blast and rust removal

钢构件在涂层之前应进行除锈处理，锈除得干净则可提高底漆的附着力，直接关系到涂层质量的好坏。本公司采用大型抛丸清理机满足这一涂装工艺的要求，使构件达到Sa3除锈等级。该机设有多个抛丸器，大型清理室，可满足各种钢构个及H型钢的表面清理要求

Steel components should be rust before the coating treatment, rust removed clean can improve the adhesion of primer, directly related to the quality of the coating. The company uses a large shot blasting machine to meet the requirements of this coating process, so that components to reach the SA3 rust level. The machine is equipped with a number of shot blasting, large cleaning room, can meet various steel and H-steel surface cleaning requirements